Skip to content
Avecas
Avecas

ATE PROGRAMMING

ATE programming

Integrate instrument resources, pin electronics and pattern execution.

Discuss your requirements
Multi-channel electronic test equipment

Representative photograph · Multi-channel electronic test equipment.

THE ENGINEERING SCOPE

Built around
your requirements.

Explore the approach ↓
01

Technical starting point

Tester platform, pin map, measurement needs and load-board interfaces.

02

Acceptance evidence

Timing sets, relay state, settling time and measurement range.

03

Delivery package

ATE project, resource map, debug procedures and correlation reports.

CLIENT GUIDE

Scope ate programming with the right evidence.

Use these technical checkpoints to make the first project review productive.

Provide before the review

  • Tester platform
  • Pin map
  • Measurement needs and load-board interfaces

Review during execution

  • Timing sets
  • Relay state
  • Settling time and measurement range

Agree for delivery

  • Ate project
  • Resource map
  • Debug procedures and correlation reports

HOW WE WORK

Clarity at each stage.

01

Allocate resources

The initial review establishes the baseline using tester platform, pin map, measurement needs and load-board interfaces. Record gaps and dependencies before implementation.

02

Configure timing

Carry out the agreed work against the reviewed baseline. For ate programming, keep the interfaces and configuration used by this stage visible to the receiving team.

03

Implement tests

Retain the intermediate artifacts and review timing sets, relay state, settling time and measurement range. Investigate failures before using these results as an input to the next stage.

04

Correlate with reference measurements

Package ATE project, resource map, debug procedures and correlation reports. Review unresolved findings against the agreed acceptance criteria and assign ownership for follow-up.

PROJECT DECISIONS

Know what moves the work forward.

Use these gates to agree readiness, review evidence and responsibility at each stage.

  1. 01

    Baseline ready

    Are the starting inputs complete enough to proceed?

    Review method and evidence

    Tester platform, pin map, measurement needs and load-board interfaces.

    Review evidence

    Record input revisions, missing material and who can resolve each dependency.

  2. 02

    Implementation reviewed

    Has the work addressed the agreed technical objective?

    Review method and evidence

    Integrate instrument resources, pin electronics and pattern execution.

    Review evidence

    Keep the intermediate artifacts with review comments and the decisions that changed the design.

  3. 03

    Evidence checked

    Can the result be reproduced and interpreted?

    Review method and evidence

    Timing sets, relay state, settling time and measurement range.

    Review evidence

    Capture the configuration, expected result, observed result and unresolved findings.

  4. 04

    Handoff accepted

    Can the receiving team use the delivery package?

    Review method and evidence

    ATE project, resource map, debug procedures and correlation reports.

    Review evidence

    Review build or execution instructions, known limitations and ownership of follow-up actions.

INPUTS & OUTPUTS

What the work involves.

The final statement of work defines the scope and acceptance criteria.

Client inputs
Tester platform, pin map, measurement needs and load-board interfaces.
Engineering sequence
Allocate resources; configure timing; implement tests; correlate with reference measurements.
Outputs to agree
ATE project, resource map, debug procedures and correlation reports.

TECHNICAL DECISIONS

Planning ATE programming.

Read the technical guide

The engineering objective

Integrate instrument resources, pin electronics and pattern execution.

The work starts from tester platform, pin map, measurement needs and load-board interfaces. The team should identify the authoritative revision of each input and record any assumptions needed to proceed. This prevents a later result from being interpreted against a different specification or configuration.

What needs technical attention

Platform-specific behaviour must be validated on the intended tester, not inferred from simulation alone.

The review centres on timing sets, relay state, settling time and measurement range. Each finding should identify the input revision, observed behaviour and supporting evidence. Distinguish a confirmed defect from a configuration issue, an unsupported case or an open engineering question before deciding how to resolve it.

How the work is reviewed

The practical sequence is: allocate resources; configure timing; implement tests; correlate with reference measurements. Intermediate reviews allow the client to resolve decisions while changes are still manageable. If an input changes, identify the affected activities and repeat the checks that depend on it.

The expected package comprises ATE project, resource map, debug procedures and correlation reports. Acceptance criteria should specify what the receiving team needs to reproduce, inspect or integrate these artifacts. Include known limitations and outstanding actions in that package, rather than assuming that delivery of a file implies acceptance.

Link measurements to configuration and sample history

Test and manufacturing-support work relies on traceable device, board and measurement information. Keep sample identity, lot or revision, fixture version, instrument settings and environmental conditions with the results. Establish how limits are chosen and which reference measurements support them. A result without these conditions can be difficult to compare after a fixture, device or software change.

Correlation should precede optimisation. Compare repeated measurements, investigate setup sensitivity and distinguish contact or fixture failures from device behaviour. When looking at yield, segment data by the relevant conditions instead of treating an aggregate trend as a root-cause finding. Changes to test order, settling time or limits can affect the distribution and must be recorded.

Coordinate release requirements with the actual assembly, test or fabrication partner. Confirm the format and ownership of interface files, test programs and acceptance records. Design engineering support does not imply ownership of a manufacturing line, procurement responsibility or qualification authority. Destructive analysis, stress testing and sample consumption need a defined sequence and approval boundary within the project plan.

An illustrative review scenario

A device appears to fail only on one fixture. Repeat the measurement under controlled conditions, compare contacts and calibration, and use a known-good reference where available. Preserve the original failing data before changing the setup. The aim is to distinguish device failure from the measurement chain; this illustration does not establish a diagnosis for an actual sample.

BEFORE WE BEGIN

Project questions.

A clear conversation is the start of a strong engineering relationship.

What inputs are needed for ate programming?

The starting review needs tester platform, pin map, measurement needs and load-board interfaces. Share the current revision and known limitations so the scope reflects the actual design state.

What does the ate programming handoff include?

The statement of work can define ATE project, resource map, debug procedures and correlation reports. The final package should include review results and any open actions.

Which technical risks need particular attention?

Platform-specific behaviour must be validated on the intended tester, not inferred from simulation alone.

Can we start with a focused technical review?

The first work package can be a review of the available inputs and the engineering questions that must be resolved. Agree its boundaries, access requirements and expected findings before committing to a larger implementation. A review should leave an actionable list of decisions, dependencies and next steps.

How are changes and unresolved findings handled?

Tie each finding to the relevant revision and supporting evidence. A change should identify the affected interfaces, activities and checks. Confirm its effect on scope and delivery with the responsible owner. At handoff, distinguish closed findings, accepted limitations and open work so that a file transfer is not mistaken for technical acceptance.

PUT THE WORKFLOW IN CONTEXT

Explore the engineering decisions.

Practical reading to help prepare your project discussion. Studies are illustrative; they do not report client results.

Connecting DFT deliverables to manufacturing test ↗

YOUR NEXT CHAPTER STARTS HERE

What will you
build next?

Bring us your engineering challenge.
Let’s define the path from idea to implementation.

Start a conversation